Page 69 2Wire gateway was last restarted, and the elapsed time since the last line search initialization. The mxnual is functioning properly. Wireless this field is present only on wireless 2Wire gateway models Transmit The cumulative number of frames transmitted over the The Advanced — Configure Services page allows you to enable the 2Wire gateway to operate in bridged mode, change the timeout settings for NAT, enable notification messages, enable the SIP ALG, and change the upstream maximum transmission rate. The parameters are set by broadband provisioning. To change this mxnual, from the pull-down menu select Username or Phone Number. If you have performed a reset of your HG-B device or not changed the defaults, you should be able to access it with the following settings:.

Author:Mukasa Kagazshura
Language:English (Spanish)
Genre:Health and Food
Published (Last):16 March 2013
PDF File Size:4.46 Mb
ePub File Size:3.95 Mb
Price:Free* [*Free Regsitration Required]

Converting your regular telephone line to DSL can cause high-pitched tones and static when using the phone. Installing a filter on every telephone or telephone device sharing the same telephone number as your DSL1 separates these signals and eliminates the noise.

Locate the phone jack where you want to connect your 2Wire gateway. Insert the DSL filter into the jack. If you have a phone, answering machine, fax machine, satellite TV equipment, or other phone device in this jack location, plug it into the filter port labeled PHONE. Install a DSL filter on all other phone devices in your house such as dial-up modems, fax machines, caller ID devices, and set top boxes. Lift the telephone from the wall pegs and disconnect the phone cord from the wall jack.

Connect the telephone cord from the back of the DSL filter into the wall jack. Align the keyhole slots on the filter with the wall plate pegs and press down gently to secure. Connect the telephone cord to the phone jack located on the front of the mounted filter.

Attach the telephone to the mounting pegs on the DSL filter and your installation is complete. Note: The extra phone jack located at the bottom of the filter labeled LINE is provided should you wish to connect your gateway at this phone connection.

Gateway Connected Via Ethernet 1. Wireless adapters can be purchased from your service provider. Figure 2. Gateway Connected Via Wireless 1. If you are NOT using a 2Wire wireless adapter, you must manually configure your adapter to communicate with the gateway using the information on page 6. Beneath the serial number is a ten-digit number which is used as the encryption key. These are located on the bottom of your gateway shown in horizontal orientation.

You will need this information to configure your wireless adapter. Configuring the Adapter 1. The encryption key is a bit hex value, located beneath the bar code on the bottom of the 2Wire gateway. In the example, it is If the Add Hardware Wizard displays, follow the on-screen instructions. After the driver installs click Finish to complete the driver installation.

The Setup Wizard will resume when your PC has rebooted. Double-click the 2Wire CD icon on your desktop. Double-click 2Wire USB to begin the driver installation. If you have set up an administrator name and password, the Authenticate screen opens. Enter your administrator name and password and click OK. Follow the on-screen instructions. When the driver installation is complete, you will be prompted to restart your computer. Insert the 2Wire CD and follow the on-screen instructions.

If prompted by the Setup Wizard, enter the digit key code you received from your service provider. If you were not provided with a key code, contact your service provider.

Macintosh OS X and operating systems other than those stated above must perform a manual configuration of the gateway. Insert the 2Wire CD. Double-click the 2Wire icon. Double-click the 2Wire Setup Wizard icon.

Use any of the following methods to connect additional computers to your network. Connection Type.



Below are the device manuals available for your HG-B. Instant Repair Help over the Phone 6ya. Is there a. Helpful 26 Not Helpful Comment Flag. Answer questions, earn points and help others Answer questions. Hard reset instructions for 2Wire HG-B If your HG-B router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Not sure if they can change it but looking up the default gateway ip address will give you the router ip address if DHCP is being used and if it has changed somehow?


2Wire 2701HGV-W Installation Manual

Shakarr The Traceroute test traces the number of times a data packet sent from IP device often Ethernet with one or more ports for connecting analog telephones. Page 82 If trouble is experienced with this equipment, please contact the store, reseller, or agent from whom the product was purchased. There are some applications and devices that require the use of specific data ports through the firewall. Notify me of new comments via email. I tried different channels, different security methods, and other things, but nothing made it faster.



Noise margin in dB at the start of the connection. In the Default Gateway field, enter the default gateway address you want the gateway to use. Incoming is the speed of data flowing from the 2wire hg-b manual to your network; Outgoing is the speed of data flowing from your network to the Internet. Hosting An Application Firewall page. Resetting The System Password System Tab To disable password protection, deselect the checkbox and click Enable SAVE To safeguard your network against unauthorized users, it is also a good practice to periodically change your password. Attach the computer to the Local Network port of the 2Wire gateway.

Related Articles